DIY OFF ROAD CAMPER TRAILER KIT. 1300KG RATING. ALL THE RUNNING GEAR NEEDED.

SKU : 190608672284
$1,166.00

Available



Details

DIY OFF ROAD TRAILER KIT
OUTBACK OFFROAD SPRINGS
1300KG RATED

 

STUD PATTERNS AVAILABLE
FORD (5/114.3 PCD, 1/2" STUDS AND NUTS)
COMMODORE (5/120 PCD, 7/16" STUDS AND NUTS)
HQ (5/120.65 PCD, 7/16" STUDS AND NUTS)
HT (5/108 PCD, 7/16" STUDS AND NUTS)
6 STUD L/C (6/139.7 PCD, 1/2" STUDS AND NUTS)
5 STUD L/C (5/150 PCD, 9/16" STUDS AND NUTS)
D40/NP300/PATHFINDER (6/114.3 PCD, 1/2" STUDS AND NUTS)
F100/JEEP (5/127 PCD, 1/2" STUDS AND NUTS)

 

IN THIS KIT
1X 45MM SQUARE SOLID AXLE WITH ELECTRIC BRAKE MOUNTS WELDED, ALSO COMES WITH SPLIT PINS & WASHERS (GIVE SPECIFY HUB FACE TO HUB FACE MEASUREMENT AND WE WILL MATCH IT UP)
AVAILABLE IN 64", 65", 66, 67", 68", 69", 70", 71", 73", 75", 77", 78", 79", 81", 83",85", 87", 89", 91", 93", 94", 96" ( TIP TO TIP)
2X 6 LEAF 60MMX7MM OFF ROAD BLACK SPRINGS WITH DAMPNERS (RATED 1300KG) (SPRINGS ARE SHOT PEENED FOR EXTRA STRENGTH)
2X FRONT HEAVY DUTY HANGERS HANGERS
2X REAR EYE EXTRA STRENGTHENED HANGERS
2X OFF ROAD FISH PLATES
4X OFF ROAD 5/8" HIGH TENSILE U BOLTS
2X GREASABLE HIGH TENSILE SHACKLE PLATES WITH SHACKLE BOLTS WELDED
2X GREASABLE HIGH TENSILE SHACKLE PINS
2X AXLE PADS
1X LEFT HAND 10" BRAKE BACKING PLATE WITH HAND BRAKE LEVER
1X RIGHT HAND 10" BRAKE BACKING PLATE WITH HAND BRAKE LEVER
2X 10" HUB DRUMS WITH CUPS ALREADY PRESSED IN (AVAILABLE IN 6 STUD LANDCRUISER, 6 STUD D40/NP300, 5 STUD LANDSCRUISER, 5 STUD JEEP/F100, 5 STUD FORD, 5 STUD COMMODORE, 5 STUD HT OR 5 STUD HQ)
2X BEARING SETS (2X SLIM LINE INNER BEARINGS, 2X SLIM LINE OUTER BEARINGS, 2X WASHERS, 2X SPLIT PINS, 2X DUST SEALS, 2X DUST CAPS)
1X 360 DEGREES POLY BLOCK WELD ON COUPLING WITH HARD CHROME SHAFTING
POLY BLOCK CAR ADAPTOR AND SPRING PIN
1X POLY COUPLING HAND BRAKE KIT
2 X DROP DOWN CORNER STEADIES WITH SWINGING BIG FOOT FOR STABILITY
1X CORNER STEADY HANDLE
1X 10" SWING UP WELD ON JOCKEY WHEEL
1X WELD ON POLY BLOCK OFF ROAD COUPLING WITH HARD CHROME SHAFTING. ALSO COMES WITH 4MM HAND BRAKE CABLE (8 METRES), CABLE ADJUSTER AND 2 WIRE CLAMPS

EXTRAS AVAILABLE
JAPANESE KOYO BEARINGS $40 (click on link below)
2" OR 4" DROP AXLES $295
ASSEMBLE OF AXLE $50EXTRAS AVAILABLE

"CLICK HERE TO UPGRADE TO JAPANESE MANUFACTURED BEARINGS"

 

,

Long Part of spring to the front, move rear hanger 25mm towards the rear,
Centre to centre of the hangers needs to be 25mm greater than centre to centre of the springs


SHOT PEENING
Shot peening is a cold working process used to produce a compressive residual stress layer and modify mechanical properties of metals and composites. It entails impacting a surface with shot with force sufficient to create plastic deformation. Shot peening is often called for in aircraft repairs to relieve tensile stresses built up in the grinding process and replace them with beneficial compressive stresses.