DIY 2000kg GVM TANDEM TRAILER KIT, SPRINGS HYDRAULIC DRUM BRAKES. STUB AXLES

SKU : 362419905221-6
$825.00

Available



Details

DIY TANDEM TRAILER KIT
2000KG RATED
HYDRAULIC DRUM BRAKES. SLIPPER SPRINGS, SPECIALLY MACHINED STUB AXLES

STUD PATTERNS AVAILABLE
FORD (5/114.3 PCD, 1/2" STUDS AND NUTS)
COMMODORE (5/120 PCD, 7/16" STUDS AND NUTS)
HQ (5/120.65 PCD, 7/16" STUDS AND NUTS)
HT (5/108 PCD, 7/16" STUDS AND NUTS)
6 STUD L/C (6/139.7 PCD, 1/2" STUDS AND NUTS)
5 STUD L/C (5/150 PCD, 9/16" STUDS AND NUTS)

IN THIS KIT
X2 45MM SQUARE SOLID STUB AXLES MACHINED TO SLEEVE INTO 50X50X5MM R.H.S BOX SECTION WITH HYDRAULIC DRUM MOUNTS WELDED. 1000KG RATED PER PAIR.
X2 45MM SQUARE SOLID STUB AXLES MACHINED TO SLEEVE INTO 50X50X5MM R.H.S BOX SECTION. 1000KG RATED PER PAIR.
2X 9" HYDRAULIC DRUM BACKING PLATES WITH HIGH TENSILE BOLTS AND NUTS FOR FIXING TO BRAKE MOUNT
2X 9" HYDRAULIC BRAKE DRUMS. (CUPS ALREADY INSERTED INTO DRUMS)
2X LAZY HUBS (CUPS ALREADY INSERTED INTO DRUMS)
4X S/L BEARING KITS INCLUDING DUST SEALS AND DUST CAPS
ALL WHEEL NUTS
4X 6 LEAF SLIPPER SPRINGS WITH NYLON BUSHES. RATED 1200Kg PER PAIR (SPRINGS ARE SHOT PEENED FOR EXTRA STRENGTH)
2X FRONT SLIPPER HANGERS
2X REAR SLIPPER HANGERS
2X MIDDLE LARGE SLIPPER HANGERS
4 X FISH PLATES
8 X 50MMX 150MM 1/2" U BOLTS WITH NUTS AND WASHERS
4 X AXLE PADS
1X 2000KG OVERRIDE BALL COUPLING
1X 3/4 MASTER CYLINDER BRACKET
1X 3/4 MASTER CYLINDER WITH MOUNTING BOLTS
1X 4 HOLE COUPLING WELD ON PLATE
4X COUPLING HIGH TENSILE BOLTS, NUTS AND WASHERS
1 X 300MM MALE/FEMALE FLEXI HOSE
1X 2500MM COUPLING TO AXLE MAIN FLARED BUNDY LINE WITH NUTS (LET US KNOW IF LONGER IS REQUIRED)
1X 1500MM FLARED BUNDY LINE WITH NUTS
1X 500MM FLARED BUNDY LINE WITH NUTS
1X BRASS T PIECE
1X MASTER CYLINDER NUT AND WASHER
ALL COPPER FITTINGS AND T PIECES TO COMPLETE AXLE AND FINISH OFF AT COUPLING WITH PRE FLARED LINES!!

Please check coupling to axle hydraulic line length. if longer is required please get in contact with us

When ordering please supply your stud pattern

upgrade to the easy instillation hydraulic line setup.
12ft set up: $70 (click on link below)
16ft set up: $75 (click on link below)

"UPGRADE TO 12FT FULL FLEXI KIT BY CLICKING HERE"

"UPGRADE TO 16FT FULL FLEXI KIT BY CLICKING HERE"   

 

EXTRAS AVAILABLE
JAPANESE MANUFACTURED BEARINGS $100 (CLICK ON LINK BELOW)

 "CLICK HERE TO UPGRADE TO JAPANESE MANUFACTURED BEARINGS"

 

SHOT PEENING
Shot peening is a cold working process used to produce a compressive residual stress layer and modify mechanical properties of metals and composites. It entails impacting a surface with shot with force sufficient to create plastic deformation. Shot peening is often called for in aircraft repairs to relieve tensile stresses built up in the grinding process and replace them with beneficial compressive stresses.