DIY 2800Kg Hydraulic Disc Boat trailer Kit. Rocker roller, Alko IQ7, Axles 64" - 77" Long

IN THIS KIT
2X 45MM GALVANISED SQUARE AXLES WITH 10" HYDRAULIC DISC FLANGES WELDED. AVAILABLE IN 64", 65", 66, 67", 68", 69", 70", 71", 73", 75", 77" ( TIP TO TIP) (PLEASE NOTE THE FLANGES ARE WELDED TO AXLE AFTER IT IS GALVANISED AND COLD GALVANISE IS APPLIED WHERE THE FLANGES HAVE BEEN WELDED) AXLES RATED 1400KG EACH
4X GALVANISED HYDRAULIC DISC BRAKE CALIPERS WITH STAINLESS STEEL PISTONS AND ZINC MOUNT BOLTS
4X BRAKE PADS
4X 10" GALVANISED DACROMET BRAKE DISCS. 15MM THICK DISCS (CUPS ALREADY INSERTED INTO DISCS)
4X SLIMLINE BEARING KITS INCLUDING MARINE SEALS AND DUST CAPS.
ALL WHEEL NUTS TO SUIT STUD PATTERN PROVIDED
1X 6 LEAF 3000KG GALVANISED DACROMET ROCKER ROLLER LOAD SHARING SPRING SET WITH ALL GREASABLE HIGH TENSILE SHACKLE BOLTS & STEEL BUSHES. (SPRINGS ARE SHOT PEENED FOR EXTRA STRENGTH)
4X GALVANISED FISH PLATES
8X GALVANISED 45MM X 150MM 5/8" HIGH TENSILE U BOLTS WITH NUTS AND WASHERS
4X GALVANISED AXLE PADS
1X 3500KG GALVANISED DACROMET ELECTRIC 50MM BALL COUPLING
1X ALKO IQ7 ACTUATOR WITH BUILT IN BRAKEAWAY UNIT
1X 4 HOLE COUPLING WELD ON PLATE
4X HIGH TENSILE COUPLING BOLTS AND AND NYLOC NUTS
1X 6100MM COUPLING TO FRONT AXLE MAIN FLARED BUNDY LINE WITH NUTS (LET US KNOW IF LONGER IS REQUIRED)
2X 2000MM FLARED BUNDY LINE WITH NUTS
3X 500MM FLARED BUNDY LINE WITH NUTS
3X 400MM MALE / FEMALE FLEXI LINES
1X BRASS T PIECE
1X BRASS 4 WAY BLOCK
1X MASTER CYLINDER BRASS NUT AND WASHER
ALL BUNDY TUBING, FLEXI HOSES & BRASS FITTINGS TO COMPLETE BRAKES.

Please check coupling to front axle hydraulic line length. if longer is required please get in contact with us
On ordering please provide your stud pattern and axle length?


EXTRAS AVAILABLE
2" OR 4" DROP AXLES $295 EACH AXLE. DROP AXLES TAKE APPROX 5 DAYS TO ENGINEER
ASSEMBLE OF AXLE $50 PER AXLE
JAPANESE MANUFACTURED BEARINGS $100 (CLICK ON LINK BELOW)
GULL WING AXLES $180 PER AXLE
TANDEM RUBBER FLEXI KIT $90
TANDEM STAINLESS FLEXI KIT $160
HUNTSMAN STAINLESS CALIPERS AND DISCS (POA)

 "CLICK HERE TO UPGRADE TO JAPANESE MANUFACTURED BEARINGS"

SHOT PEENING
Shot peening is a cold working process used to produce a compressive residual stress layer and modify mechanical properties of metals and composites. It entails impacting a surface with shot with force sufficient to create plastic deformation. Shot peening is often called for in aircraft repairs to relieve tensile stresses built up in the grinding process and replace them with beneficial compressive stresses.


DACROMET®
DACROMET®, is the leading inorganic coating commonly specified in the wind turbine, heavy truck, marine, agricultural, construction equipment and aerospace industries. A water-based, VOC-compliant coating, DACROMET® is comprised mainly of overlapping zinc and aluminum flake in an inorganic binder.